RPM882-H14 
 
Photo Link Module
 
 
 
8/9 
 
Attached components 
Recommended values
Part symbol
C1
Recommended value
Notice
1礔, tantalum or ceramic
Ex.) TCFGA1A105M8R (ROHM)
Bigger capacitance is recommended with much noise from power supply
R1
4.7&?%, 1/8W
(VLEDVCC=3V)
At LED Emitting Duty=20%
 
 
[LED current set-up method for Remote control mode]
In case of using R1 with different condition from the above, formula is as follows :
LED resistance value : R1[&], LED average consumption current : ILED[mA], Supply voltage : VLEDVCC[V],
minimum necessary of irradiant intensity le1 [mW / sr]
(Including LEDs distribution within ?5deg)
 
R1=166 ?(VLEDVCC1.28) / le15.0
ILED=Duty ?(VLEDVCC1.28) / (R1+3.5)
 
Duty : LED duty at emitting
 
 
 Please set up to be ILED / Duty < 250[mA] (Duty d 50%)
 
 At IrDA Mode, LED current is constantly approximately 40mA.
 
 
(Reference) In case of using R1, typical intensity (le1typ) and maximum intensity (le1max) on
axis are described as below.
   
le1typ=300 ?(VLEDVCC1.28) / (R1+3.5)
 
le1max=600 ?(VLEDVCC1.28) / (R1+3.5)
 
 
Notes
1) LEDVCC (8pin), VCC (3pin) and VIO (2pin)
"
 
Other power source can be used difference between LEDVCC and VCC and VIO.
(VIO < VCC + 0.3V)
 
2) Caution in designing board lay-out
To get maximum potential from RPM882-H14, please keep in mind following instruction.
 
"
The line of RXD (6pin) should be connected at backside via through hole close to RPM882-H14 pin lead. Better not to
  be close to photo diode side (1pin).
襎his is to minimize feedback supplied to photo diode from RXD.
"
 
As for C1 between 1-3 pin should be placed close to RPM882-H14.
"
 
Better to be placed more than 1.0cm in radius from photo diode (pin1 side) and also away from the parts which
  generates noise, such as DC / DC converter.
 
3) Notes
"
Please be sure to set up the TX-RC (4pin) and the TXD (7pin) input to be L (under 0.3V) except transmitting data
  (for < 90祍, ON duty d 50%).
"
 
Power down current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode.
"
Please use by the signal format at IrDA operating mode which is specified by IrDA Ver1.2 (2.4k to 115.2kbps). There
might be on error if used by different signal format.
"
Please pay attention to the lens carefully.
  Dusts of scratch on the lens may effect the characteristics of product. Please handle it with care.
相关PDF资料
RPM960-H14E3A MODULE IRDA 1152KBPS 8SMD
RPM971-H14E3A MODULE IRDA 5MBPS 8SMD
RPM972-H14E3A MODULE IRDA 4MBPS 3V SMD
RPM973-H11E2A MODULE IRDA 4MBPS FIR COMPATBL S
RPM973-H16E4A MODULE IRDA 4MBPS FIR COMPATBL S
S0106H0012XHAGNX420 RESOLVER 1" HOUSED W/TRANSFORMER
S0106H0012XHAGNY420 RESOLVER 1" HOUSED W/TRANSFORMER
SA.PANEL.20 ANT 17DBI BASE STATION W/N
相关代理商/技术参数
RPM882-H14E2A 功能描述:光纤发射器、接收器、收发器 IRDA IR COMM SIDE VIEW W/SHIELD RoHS:否 制造商:Omron Electronics 产品:Transmitters 数据速率:3.5 Gbps 波长:850 nm 最大工作温度: 最小工作温度: 封装 / 箱体: 封装:
RPM882-H7 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module
RPM882-H7E2 制造商:ROHM Semiconductor 功能描述:IRDA COMMUNICATION MODULE SIR - Tape and Reel 制造商:ROHM Semiconductor 功能描述:IC IRDA IR COMMUNICATION MODULE 制造商:ROHM Semiconductor 功能描述:IRDA COMM MOD SIR
RPM90 功能描述:测试引线 IND. TRIGGER PICK RoHS:否 制造商:Pomona Electronics 设备类型:Patch Cords 连接器类型:Banana plug (stackable) on both ends 长度:60 in 颜色:Black
RPM922-H11 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module
RPM922-H11E2A 功能描述:光纤发射器、接收器、收发器 IRDA TXRX 0.1152MBPS 3V 7PIN RoHS:否 制造商:Omron Electronics 产品:Transmitters 数据速率:3.5 Gbps 波长:850 nm 最大工作温度: 最小工作温度: 封装 / 箱体: 封装:
RPM960-H14 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module
RPM960-H14_05 制造商:ROHM 制造商全称:Rohm 功能描述:IrDA Infrared Communication Module